Pool or Spa Turning On and Off Randomly
This article will focus on one quick fix to the problem of a pool or spa
turning on and off randomly written by www.WCPandS.com. This is for in ground pools or spas using a Jandy AquaLink
controller with a wired remote (see pictures below if you are not sure that
it’s the same as yours). Above ground pools or spas would not apply to this
article. The features that can be affected include pool and spa lights, spa
booster pump, and the heater (may be connected to the system’s preprogrammed setting
marked as “Spa Mode”). The problem is
when these features randomly turn on and off.
Check your controller (usually in the house) and make sure whatever is coming on is not part of the normal schedule. If you are not sure how to do this, it is in the manual.
Check your controller (usually in the house) and make sure whatever is coming on is not part of the normal schedule. If you are not sure how to do this, it is in the manual.
Note: This article is how we would attempt to fix this issue. Wine Country
Pools is not responsible for any damages or injuries incurred by following this
article. If you are unsure about step seek a local swimming pool professional.
A common cause of this problem is a leaking remote. The remote is the 4
bottom key pads that are wired to the main system controller usually in the spa
but sometimes just outside but next to the spa. The key pads are set to control
the spa booster pump, “Spa Mode”, and the pool/spa lights.
In the picture above you can see one version of what the spa remote
looks like. Notice how this one is in the middle position of the tile.
In the picture above notice how the water is now at the controls as the
system is running. When the remote develops a leak, water gets inside and
completes an electrical connection for one or more of the buttons causing that
function to turn off and on repeatedly. On some spas the remote is just above
the water line so water gets in when either the spa jets come on or when users get into the spa for use, both
of which cause the water level to rise.
To begin turn off the power to
the pool and spa controller.
The best way to do this is to turn off all breakers either at the
controller or at the house power panel.
Remove or turn the 9 volt battery cover.
Remove the 4 screws holding the AquaLink control panel cover on with a
flat head screw driver.
The top of the cover needs to be pulled out then up from the bottom
slots to be completely removed.
At the top of the panel you will see the control board with the wires
connecting to the top.
Usually there is a large sticker showing a wiring diagram and listing
what each connection corresponds to. This will fade or fall off over time. If yours is missing or unreadable see the
included picture for reference.
At the top of the board, the 2nd set of connectors on the left is for
the remote. These six wires need to be removed.
Do not cut these wires as you may need to reconnect them. These can be
unscrewed with a small screwdriver.
Twist the wires together and push them out of the way.
Insert and screw in the 4 screws with a flat head screw driver.
Push down or reattach the 9 volt battery cover.
Turn the breakers back on.
Check if your system is working correctly,
turn it on in pool mode and watch to see if it is still randomly turning
features on and off. It may take a few days to tell if your system is working
correctly.
Thank you so much for letting us know this one. I'm not familiar in pool supplies. But I'm willing to buy all that just to have like this spa turning and off randomly. I hope I can have it as soon as possible. Keep on sharing!
ReplyDeletePool Heater Repair
ReplyDeletePlease let me know if you're looking for link mega888 a writer for your weblog. You have some really good posts and I feel I would be a good asset. If you ever want to take some of the load off, I'd absolutely love to write some material for your blog in exchange for a link back to mine. Please blast me an email if interested. Regards!
thanks for the post as it was the problem I was experiencing. I had known about the spa switch and had told my pool service guy to disconnect it but when I got a new Jandy controller they hooked it up.
ReplyDeleteThanks so much for your help - this solved my problem. My question now is what should I do with the spa remote? Should I replace, clean, or permanently disable it?
ReplyDeleteSpa in Al Barsha
ReplyDeleteSpa Center in Ajman
ReplyDeleteBody Massage Center in Deira
ReplyDeleteMassage in Al Rigga
ReplyDeleteThank you very much for the detailed explanation :) https://hairsalonculvercity.com/
Custom Pools Denver Co - We offer custom swimming pools in Denver CO. We are a professional Denver pool builder and one of the best pool construction companies in Denver, Colorado. Contact us now! Custom Swimming Pools in Denver, Colorado and Top-Rated Denver Pool Builders. Check our Services Here!
ReplyDeleteKeep sharing such updates. High and low weight engineered package boiler supplier offers low cost high and low weight steam boilers. Put in your request online for a high and low weight steam boiler.
ReplyDeleteswimming pool heater Lancaster County, PA
It sounds like it could be an issue with your timer or electrical connections. Check those first or consider consulting a professional to avoid further issues.Five Star Custom Pools.
ReplyDeleteHaving your pool or spa turn on and off randomly can be frustrating! Check for loose wiring or faulty timers to ensure uninterrupted relaxation.Social Cali-Manteca.
ReplyDelete